Subaru Legacy

since 1990-1998 release

Repair and operation of the car



Subaru Legacy
+ 1.1. Identification numbers
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. Suspension bracket
+ 12. Steering
- 13. Body
   13.1. Introduction
   13.2. Care of a body
   13.3 Care of an upholstery and rugs
   13.4. Repair of insignificant damages of a body
   13.5. Repair of strong damages of a body
   13.6. Cowl
   13.7. Replacement of the lock of a cowl
   13.8. Replacement of a cable of the lock of a cowl
   13.9. Front grille
   13:10. Front bumper
   13:11. Rear bumper
   13:12. Forward wing
   13:13. Door upholstery
   13:14. Lock, cylinder of the lock and handle of opening of a door
   13:15. Door glass
   13:16. Window regulator
   13:17. External mirror
   13:18. Doors
   13:19. Trunk lid
   13:20. Luggage carrier lock
   13:21. Cable of opening of the lock of a luggage carrier
   13:22. Replacement of racks of support of a back door
   13:23. Back door
   13:24. Lock of a back door, external handle and cylinder of the lock
   13:25. Casings of a steering column
   13:26. Central console
   13:27. Dashboard elements
   13:28. Dashboard
   13:29. Air inlet lattice
   13:30. Front seats
+ 14. Electric equipment






13:11. Rear bumper

GENERAL INFORMATION

Details of a rear bumper of the car with a body "station wagon" from 1990 to 1994

 
1 – side arm
2 – bumper beam
3 – power absorber
4 – molding
5 – overlay of a bumper
6 – top clamp
7 – arm
8 – lower central clamp
9 – lower side clamp

Details of a rear bumper of cars with a body "station wagon" since 1995

.
1 – bumper beam
2 – side arm
3 – overlay of a bumper
4 – power absorber

Arrangement of a bolt of fastening of a forward part of a rear bumper


Arrangement of bolts of fastening of an overlay of a bumper


Arrangement of a bolt of fastening of a hook in the luggage compartment


Arrangement of the plastic caps closing access to bolts of fastening of a bumper


Arrangement of side bolts of fastening of a bumper


PERFORMANCE ORDER
1. Lift a back part of the car and record on supports. Remove back wheels.
2. Unscrew screws (are specified by shooters) and remove back mudguards from wheel arches.
3. Unscrew internal and lower bolts of fastening of an overlay of a bumper (see rice. Arrangement of a bolt of fastening of a forward part of a rear bumper, Arrangement of bolts of fastening of an overlay of a bumper).
4. Remove back internal finishing of a luggage carrier. Take caps and unscrew two screws from each party of fastening of a bumper (see rice. An arrangement of a bolt of fastening of a hook in the luggage compartment, the Arrangement of the plastic caps closing access to bolts of fastening of a bumper, the Arrangement of side bolts of fastening of a bumper).
5. Slightly put forward a bumper from the car, disconnect from it electric sockets and finally remove a bumper.
6. Installation is made in the sequence, the return to removal.
7. At installation of a rear bumper on models from 1990 to 1994 check that hooks are correctly combined with body panels.
8. At installation of a rear bumper on models since 1995 install rams on a bumper.
9. An arrangement of the directing pins on which it is necessary to install bumper rams on models since 1995.
10. At installation of a rear bumper on models since 1995 record a bumper in body flutes.